Ubiquiti PowerBeam 5AC 300 Feed PBE-5AC-300-FEED in Dubai, UAE
This model-specific feed assembly is intended for buyers maintaining or restoring a compatible PowerBeam 5AC 300 deployment. Because feed-only listings can be confused with complete bridge kits, FourTeck helps confirm the exact unit, package contents, regional version and installation requirement before quotation.
Confirm before ordering
Share the label photo, reflector size, required quantity, preferred condition and deployment location.
Feed/radio assembly
PowerBeam 5AC 300
Compatibility confirmation
Confirm current options
Direct answer for buyers
The PBE-5AC-300-FEED is best understood as the detachable feed and radio portion associated with the original Ubiquiti PowerBeam 5AC 300 system, rather than a guaranteed complete dish kit. It is mainly considered when an existing reflector and mount remain serviceable but the active feed unit requires replacement, or when an integrator needs a matching component for a controlled wireless project. Buyers should confirm the exact label, region, firmware condition, Ethernet and PoE requirements, included parts and reflector compatibility before proceeding. They should also establish whether the requirement is for a single replacement unit or a matched pair for a new point-to-point link.
What the feed assembly does
In the PowerBeam design, the feed section contains the active outdoor radio and directs radio-frequency energy toward the dish reflector. Ubiquiti’s integrated feed approach avoids a separate radio-to-antenna coaxial cable, reducing cable loss and simplifying the physical arrangement. When installed with the correct reflector, mounting system, power source and network cabling, the assembly becomes part of an outdoor airMAX ac wireless bridge.
A feed-only unit cannot deliver the intended antenna gain by itself. The reflector shape and diameter contribute materially to the directional pattern, gain and interference rejection of the complete system. For this reason, a buyer replacing only the feed should not assume that any similar-looking Ubiquiti dish is suitable. Model matching and mechanical fit must be checked.
Who should consider it
This component may be appropriate for wireless internet service providers, network contractors, hospitality sites, warehouses, schools, construction compounds, CCTV integrators and multi-building businesses that already operate a compatible PBE-5AC-300 installation. It can also be relevant to maintenance teams holding spare reflectors and mounts.
It is less suitable for a buyer who needs a ready-to-install bridge and does not already possess the dish, mount, PoE adapter and related hardware. In that case, requesting a complete current bridge model may be more practical. FourTeck can compare the replacement route with a complete-device alternative after reviewing the site and the condition of the existing equipment.
Business problems this component can help address
Damaged active radio
A site may have an intact reflector and mounting structure but a failed, water-damaged or electrically damaged radio feed. A correctly matched replacement can reduce unnecessary mechanical rework.
Spare-parts continuity
Operators with several legacy PowerBeam 5AC 300 links may keep feed assemblies for controlled maintenance. The spare strategy should include revision, regional and condition checks.
Cost-aware restoration
Replacing only the failed portion may be considered when the remaining structure is verified as serviceable. Labour, alignment effort and lifecycle risk should still be compared with a complete replacement.
Project standardisation
A matching feed can help maintain a common configuration across an existing network, although firmware support, security settings and long-term availability must be reviewed.
Product-fit decision matrix
| Requirement | Suitable when | Confirm before ordering |
|---|---|---|
| Replace an existing feed | The reflector, bracket and cabling are serviceable | Exact model label, mechanical fit and regional version |
| Build a new wireless bridge | All compatible parts and a matched remote endpoint are available | Whether a complete newer bridge is more appropriate |
| Maintain legacy standardisation | Existing operational procedures depend on this platform | Firmware, security, lifecycle and spare strategy |
| Outdoor point-to-point link | The site has clear line of sight and appropriate mounting | Link budget, frequency rules, channel plan and alignment |
Verified platform information and item-specific cautions
| Brand | Ubiquiti |
|---|---|
| Item requested | PBE-5AC-300-FEED feed/radio assembly |
| Associated platform | PowerBeam 5AC 300, model PBE-5AC-300 |
| Wireless band | 5 GHz; permitted frequencies and power are region dependent |
| Complete-system antenna gain | 22 dBi when used as the specified PBE-5AC-300 complete 300 mm system; not a feed-only gain claim |
| Ethernet interface | One 10/100/1000 Ethernet port on the associated PBE-5AC-300 platform |
| Power method | Passive PoE, associated platform specification 20–26 V DC; confirm injector inclusion and compatibility |
| Associated maximum power consumption | 5.5 W for the complete PBE-5AC-300 platform according to the original datasheet |
| Management platform | airOS generation and supported firmware depend on hardware revision |
| Included components | Not confirmed; feed-only quotations must state whether PoE adapter, cable cover, reflector or mount is excluded |
| Condition | New, refurbished, pulled or project-sourced condition must be confirmed in writing |
| Availability | Contact FourTeck for current options, quantity and lead-time guidance |
Compatibility and package dependency notice
The suffix “FEED” is commercially important. It normally indicates that the active feed/radio portion is being offered separately from the full reflector assembly. Buyers should request a written bill of materials showing exactly what is included. A photo of the label and connector area is useful because visually similar PowerBeam generations and reflector sizes may not be interchangeable. The network engineer should also verify that the intended PoE injector uses the correct passive voltage and polarity. Connecting unsupported power equipment can damage an outdoor radio.
Compatibility should not be inferred only from the product family name. Reflector diameter, feed mount geometry, hardware revision, firmware path, country code, allowed channels and remote-end radio configuration all affect whether the part can be used successfully. FourTeck can review these details, but final wireless performance remains dependent on site conditions, alignment, interference, legal frequency limits and the quality of the complete installation.
A practical replacement and purchase journey
Identify the existing unit
Record the full model, regional suffix, MAC label, hardware condition and firmware information where accessible.
Inspect retained parts
Check the reflector, feed support, mount, Ethernet cable, surge protection, PoE source and grounding arrangement.
Confirm the replacement scope
Decide whether feed-only replacement, a full matching unit or migration to a current platform is the sensible route.
Quote and coordinate
Confirm quantity, condition, package contents, destination, installation scope and expected project schedule.
Directional wireless performance depends on the complete antenna
The PowerBeam platform concentrates energy in a narrow direction through the relationship between its feed and reflector. This directional behaviour can improve the usable signal at the intended remote site and reduce reception of unwanted signals arriving from other directions. The feed assembly alone does not reproduce the specified 22 dBi complete-system antenna gain. A bent, incorrectly sized or poorly aligned reflector can materially reduce link quality.
For a replacement project, technicians should check that the reflector has not twisted, corroded or shifted on the pole. Even when the radio powers up correctly, weak modulation rates, unstable throughput or high retransmission levels can result from alignment errors, obstructed Fresnel clearance, interference or damaged cabling. A link survey and careful realignment are therefore part of responsible restoration.
airMAX ac operation and network matching
The associated PBE-5AC-300 platform uses Ubiquiti airMAX ac technology for outdoor wireless links. It supports selectable channel widths and point-to-point operation, while actual usable throughput depends on signal quality, channel width, interference, regulatory power limits and remote-end capability. A feed replacement should be configured to match the existing link design rather than simply copying settings without review.
The remote endpoint, encryption settings, wireless mode, channel plan, network addressing and management access should be documented before removing the failed unit. Where the original configuration cannot be recovered, the replacement may require a controlled recommissioning process. FourTeck can discuss configuration support as a separate scope, including baseline settings, link alignment guidance and handover documentation.
Power, cabling and outdoor protection
The original PBE-5AC-300 platform was designed around passive PoE and a Gigabit Ethernet interface. Buyers must confirm the correct injector voltage, polarity and cabling arrangement before connection. Passive PoE is not interchangeable with every standards-based PoE source. Incorrect power can create immediate equipment risk.
Outdoor Ethernet should be suitable for the environment, routed with drip loops where appropriate and protected according to the project design. Grounding and surge protection requirements depend on the site and local practice. A replacement radio should not be installed while leaving visibly damaged connectors, cracked cable jackets or unprotected cable entries unresolved. These supporting details often determine the long-term reliability of a wireless link more than the radio replacement itself.
Ideal environments and practical use cases
A compatible PowerBeam 5AC 300 feed can support restoration of directional links between nearby buildings, warehouses, guard posts, temporary project offices, remote cameras, hospitality facilities, schools, farms and service-provider customer locations. The strongest fit is an existing installation where the reflector and mount are known to be correct and the operational team understands the original link design.
For CCTV backhaul, the engineer should calculate sustained traffic, peak recording demand and latency tolerance rather than relying on a headline radio rate. For office connectivity, the design should consider business-critical applications, redundancy and the effect of a single wireless path failure. For construction or temporary sites, pole stability, power quality and environmental exposure are significant. In every case, clear line of sight is not the only criterion; Fresnel-zone clearance, interference and legal channel availability must also be assessed.
Buyer questions to resolve before requesting a quotation
Confirm whether the reflector, mount, PoE injector and cable cover are already available and serviceable.
Provide clear photographs of model, region and regulatory markings to reduce mismatch risk.
Document its model, firmware, channel, mode and encryption settings.
State whether only new equipment is acceptable or whether verified refurbished or pulled units can be evaluated.
Separate supply-only needs from configuration, installation, alignment, testing and documentation.
Compare availability, supportability and labour with migration to a current complete bridge.
Procurement checklist
☐ Exact model and suffix from the installed label
☐ Required quantity and whether spares are needed
☐ New, refurbished or replacement-pull condition requirement
☐ Confirmation that reflector and feed bracket are retained
☐ Regional frequency and country-code requirement
☐ PoE injector voltage, polarity and inclusion
☐ Ethernet cabling and surge-protection condition
☐ Remote-end model and configuration compatibility
☐ Firmware and management-access requirement
☐ Installation, alignment and testing scope
☐ Delivery destination and project schedule
☐ Warranty or return-condition confirmation in quotation
How FourTeck can assist
FourTeck can help turn an ambiguous feed-only request into a clear procurement scope. The review may include label verification, reflector-size confirmation, package-content clarification, power requirements, quantity planning and comparison with available replacement options. For projects requiring technical services, installation, alignment, basic configuration and testing can be discussed as separate quotation items.
Buyers can also browse business technology products, review network and infrastructure services, or send project information through the FourTeck contact page.
UAE availability and support guidance
Contact FourTeck to confirm current UAE availability for the PBE-5AC-300-FEED. Availability may depend on quantity, condition, regional version, supplier channel and vendor lead time. The quotation should clearly state whether the offered item is new, refurbished, used, pulled from service or supplied as part of a wider replacement package.
Delivery and project coordination can be discussed after the exact requirement is confirmed. Where installation or configuration is required, include the site address, mounting height, existing equipment details, access restrictions and preferred schedule. Warranty guidance must be based on the actual offered condition and source rather than assumptions linked to the original complete product.
Dubai, Abu Dhabi, Sharjah and Ajman coverage
Businesses in Dubai, Abu Dhabi, Sharjah and Ajman can contact FourTeck for requirement review, quotation coordination and discussion of supply or project support. For a feed-only replacement, remote review of product labels and installation photographs is often a useful first step. Site services, where required, depend on access, location, mounting conditions and confirmed scope. Buyers should avoid removing the operational endpoint until configuration details and replacement readiness have been documented, particularly when the wireless link carries CCTV, voice, internet access or inter-building business traffic.
GCC Availability
FourTeck can assist organisations evaluating the PBE-5AC-300-FEED for projects across the GCC, including requirements connected with the United Arab Emirates, Saudi Arabia, Kuwait, Qatar, Bahrain and Oman. The first priority is to establish whether the request is for a genuine feed-only replacement or a complete outdoor bridge. Model availability, permitted frequency settings, regional coding, package contents, service options and delivery planning can vary by country and supplier channel. Buyers should provide the destination country, required quantity, existing reflector model, acceptable product condition, deployment location and expected timeline. Where a replacement is being considered for a business-critical link, FourTeck can also help compare the spare-part route with a current complete-device option. No local stock, customs outcome, fixed delivery schedule or installation date should be assumed until the exact scope and offered item have been confirmed in the quotation. For regional enquiries, buyers may also use the FourTeck Kuwait technology portal.
Africa Availability
Organisations planning wireless maintenance or replacement projects in Africa can contact FourTeck for product identification, compatibility review and procurement guidance. A feed assembly may appear simple to source, but destination, regional frequency requirements, product condition, voltage accessories, shipping arrangements and the state of the retained reflector can all affect the suitability of the purchase. Buyers should share the destination country, label photographs, quantity, preferred deployment schedule and any installation or support expectations. FourTeck can help evaluate whether the requested legacy feed remains the practical choice or whether a complete current bridge should be considered. Availability and fulfilment may depend on supplier lead time, the exact hardware revision, shipping method, local project conditions and regulatory requirements. Immediate shipment, local inventory, customs clearance and country-wide onsite coverage are not assumed. Relevant regional resources include FourTeck Africa technology solutions, FourTeck Kenya and FourTeck Uganda.
Related products, services and alternatives
Complete PowerBeam bridge
A full reflector, radio, mounting and power package may be preferable when several original components are missing or degraded.
Current airMAX bridge options
Newer models may provide a more sustainable lifecycle. Exact equivalence should not be assumed without a link and compatibility review.
Outdoor surge protection
Suitable Ethernet protection and grounding should be evaluated as part of an outdoor radio restoration project.
Installation and alignment
Physical replacement, weather sealing, precise aiming and link testing can be scoped where site support is required.
Why businesses contact FourTeck
The value of assistance on this request is practical clarity. FourTeck can help identify whether the buyer has selected the correct feed, whether a complete unit is actually required, which supporting components should appear in the bill of materials and what information is needed for a meaningful quotation. This reduces the risk of ordering a part that cannot be mounted, powered or configured at the site.
Support can also cover planning questions: whether the existing link should be restored or modernised, whether a matched pair is needed, whether the current cable and surge protection remain acceptable, and whether installation or configuration work should be included. Learn more about FourTeck or discuss a UAE technology requirement.
Frequently asked questions
Is PBE-5AC-300-FEED a complete PowerBeam?
No. The requested suffix indicates a feed/radio assembly. A quotation must confirm whether the reflector, mount, PoE adapter and other parts are excluded.
Can the feed operate without the 300 mm reflector?
It may power and transmit, but it will not provide the specified directional antenna performance of the complete PBE-5AC-300 system. It should be used only within a verified compatible assembly.
Does the feed include a PoE adapter?
Not necessarily. Package contents vary, especially for replacement, refurbished or pulled units. Injector inclusion and voltage compatibility must be written into the quotation.
Can it replace any PowerBeam feed?
No. Reflector size, mount geometry, hardware generation, regional version and firmware compatibility should be checked against the exact existing model.
Is a second unit required?
A new point-to-point bridge normally requires compatible equipment at both ends. A maintenance replacement may need only one unit when the remote endpoint remains operational.
What information is needed for a quote?
Provide label photographs, quantity, required condition, retained components, destination, remote-end model and any installation or configuration scope.
Can FourTeck configure the replacement?
Configuration assistance can be discussed based on available credentials, existing settings, remote-end details and the agreed project scope.
Is the PBE-5AC-300-FEED currently available in Dubai?
Availability must be confirmed for the requested quantity, region and condition. Model-specific legacy components may have variable supplier lead times.
Should we replace the feed or upgrade the whole link?
The answer depends on the condition of the reflector and cabling, the importance of the link, supportability, spare availability and the cost of site labour. FourTeck can help compare both approaches.
Confirm the exact feed assembly before purchase
Send the existing unit label, reflector photograph, quantity and support requirement. FourTeck will use those details to clarify compatibility, package contents and current quotation options.
Reviews
There are no reviews yet.