Managed access switching for compact business sites
HPE Aruba Networking CX 6000 8-Port Switch
The HPE Aruba Networking CX 6000 S4R22A is a non-PoE managed access switch with eight Gigabit Ethernet copper ports and two 1G SFP uplinks. It is designed for smaller branch, office and edge deployments that need enterprise-style management without the port density or power budget of a larger access switch.
What the CX 6000 8-Port S4R22A Is Used For
The HPE Aruba Networking CX 6000 S4R22A is an entry-level managed access switch for connecting a small number of wired users, printers, appliances and other Ethernet devices to a business LAN. It is best considered where eight copper access ports are enough and two 1G SFP ports meet the uplink requirement. The model is non-PoE, so devices that need power from the switch require a PoE variant or separate injectors. Before proceeding, buyers should confirm port count, uplink media, VLAN and management requirements, plus whether powered endpoints are part of the design. FourTeck can help determine the correct CX 6000 model, SFP transceivers, management approach and deployment scope for a UAE project.
Verified Technical Specifications
| Manufacturer | HPE Aruba Networking |
|---|---|
| Product number | S4R22A |
| Product type | Fully managed entry-level Layer 2 access switch |
| Copper ports | 8 x 10/100/1000BASE-T |
| Uplink ports | 2 x 1G SFP |
| Console / host | 1 x USB-C console; 1 x USB Type-A host |
| PoE capability | Non-PoE |
| Switching capacity | 20 Gbps |
| Throughput | 14.8 Mpps |
| Latency | 3.2 μs at 1 Gbps |
| Processor | Dual-core Arm Cortex-A9 @ 1016 MHz |
| Memory / flash | 4 GB DDR3 / 16 GB eMMC |
| Maximum power without PoE | 13.8 W |
| Input voltage | 100–127 VAC / 200–240 VAC |
| Operating temperature | 0°C to 40°C up to 1.5 km altitude; derating applies above that level |
Specifications should be matched to the exact S4R22A order line and current regional configuration before purchase.
Where This 8-Port Switch Fits
| Requirement | Suitable when | Confirm before ordering |
|---|---|---|
| Small wired access layer | Up to eight copper endpoints fit the local design | Allow for growth, printers, phones and infrastructure ports |
| Fibre uplink | 1G SFP connectivity is sufficient | Fibre type, distance and compatible transceiver |
| Powered devices | Endpoints have their own power | Use a PoE model if APs, cameras or phones need switch power |
| Managed LAN | VLANs, QoS, ACLs, monitoring and controlled configuration are required | Operational model: local, Central, CLI or multi-device management |
Eight Gigabit Access Ports
The eight 10/100/1000BASE-T ports support standard copper Ethernet endpoints. This is useful for a small branch, reception area, compact office pod or dedicated device segment where a larger 24- or 48-port switch would create unused capacity.
Two 1G SFP Uplinks
Two SFP ports give the switch separate uplink choices from the eight copper access ports. Buyers should match the SFP optics or copper modules to the existing fibre type, distance, connector and upstream switch compatibility before the bill of materials is finalized.
AOS-CX Management
The CX 6000 family uses the HPE Aruba Networking CX Switch Operating System. The S4R22A can be managed through HPE Aruba Networking Central, a web GUI, industry-standard CLI or Switch Multi-Edit Software, allowing the management model to be aligned with the wider network.
Layer 2 Business Controls
CX 6000 capabilities include VLAN-oriented access switching, access control lists, quality of service, traffic prioritization, sFlow monitoring, IPv6 support and static routing functions. The exact configuration should be designed around the site’s segmentation and operational requirements.
Licensing, Central Management and PoE Dependencies
The CX 6000 switch software does not require a separate switch software license or subscription for its base operation. HPE Aruba Networking Central is a separate management service, so current service entitlements, subscription terms and the intended management architecture should be confirmed when Central is part of the project.
The S4R22A is non-PoE. If the switch must power Wi-Fi access points, IP phones, cameras or other IEEE 802.3af/802.3at devices, evaluate the CX 6000 8-port Class 4 PoE model instead of assuming power is available on this unit.
Compatibility and Integration Checks
The main compatibility decision is not simply whether an Ethernet cable can be connected. The switch must fit the upstream network design, VLAN plan, uplink media and management process. For fibre connections, confirm the exact SFP transceiver type, fibre mode, wavelength and link distance. For existing Aruba environments, confirm the planned AOS-CX software level and management platform. If the site uses a third-party core or firewall, verify VLAN tagging, link configuration and monitoring expectations at both ends.
- Confirm whether 1G uplinks provide enough bandwidth for the branch or edge segment.
- Check SFP module compatibility before ordering optics.
- Confirm VLAN, trunk/access-port and QoS requirements.
- Decide whether management will be local, centralized or mixed.
- Plan IP addressing, monitoring, configuration backup and firmware maintenance.
When S4R22A May Be the Right Fit
Choose this model when the site needs a compact managed switch, eight copper ports are enough, the uplink requirement is 1G SFP, and connected devices do not need PoE from the switch. It is particularly relevant for small branches, segmented equipment areas and quiet office environments where compact deployment is useful.
When Another Model Should Be Evaluated
A different CX model may be more suitable when more than eight access ports are needed, PoE is required, or uplink bandwidth must exceed 1G. Compare the 8-port PoE CX 6000 variant for powered endpoints, or larger CX 6000 models for higher copper port density. Where faster uplinks or broader Layer 3 requirements are important, evaluate higher CX families rather than oversizing this entry-level model.
Deployment and Installation Considerations
A successful small-switch deployment still requires basic design decisions. Determine where the unit will be mounted, how power will be provided, how fibre or copper uplinks will be routed and which ports should carry each VLAN. The operating environment should remain within the manufacturer’s temperature limits. The current technical data identifies a maximum non-PoE power consumption of 13.8 W and input voltage support of 100–127 VAC or 200–240 VAC.
List current and expected wired devices.
Select fibre/copper media and compatible SFPs.
Map VLANs, port roles, QoS and management access.
Validate links, monitoring and configuration backup.
Buyer Questions Before Ordering
Procurement Checklist for the CX 6000 8-Port Switch
- Confirm product number S4R22A
- Required switch quantity
- Current and future copper port count
- PoE requirement for endpoints
- Required SFP transceiver type
- Fibre mode, distance and connector
- VLAN and uplink configuration
- Central or local management plan
- Installation and mounting location
- Configuration, testing and documentation scope
FourTeck Assistance for UAE Projects
FourTeck can help business buyers translate a small-site requirement into the correct switch and bill of materials. Assistance can include checking whether the S4R22A port count is sufficient, confirming whether a PoE variant is needed, reviewing SFP requirements, discussing management options and defining installation or configuration work before quotation.
Explore business networking products, review available installation and configuration services, or contact FourTeck for model and quotation guidance.
UAE Availability
Contact FourTeck to confirm current UAE availability for the exact S4R22A model. Availability can depend on quantity, regional supply, transceiver requirements and vendor lead time. Delivery coordination, installation and configuration scope can be included in the discussion once the requirement is confirmed.
Frequently Asked Questions
Is the CX 6000 S4R22A suitable for a small branch office?
Yes, when eight Gigabit copper access ports and 1G SFP uplinks are enough for the branch design. Growth and powered-device requirements should be checked before selection.
Can this switch power wireless access points or IP phones?
No. S4R22A is non-PoE. A PoE-capable CX 6000 model or another power method is required for devices that depend on Ethernet power.
How many SFP uplinks are available?
The S4R22A provides two 1G SFP ports. Compatible transceivers should be selected according to fibre type, distance and the upstream device.
How can the switch be managed?
Management options include HPE Aruba Networking Central, web GUI, CLI and HPE Aruba Networking Switch Multi-Edit Software. The preferred method depends on the wider network operating model.
What should be compared if eight ports are not enough?
Compare larger CX 6000 models with 12, 24 or 48 access ports, while also checking PoE and uplink requirements. A higher CX family may be appropriate if faster uplinks or broader routing capabilities are required.
Can FourTeck help with configuration in Dubai and the UAE?
FourTeck can discuss configuration and installation scope, including VLAN planning, uplinks, management access, testing and documentation. Scope and scheduling should be confirmed in the quotation.
Confirm the Right CX 6000 Configuration
Send FourTeck your required port count, PoE needs, uplink medium, SFP distance and management preference. We can help confirm whether S4R22A is the correct fit before quotation.
Reviews
There are no reviews yet.