Compact managed switching with configurable 24V passive PoE
Ubiquiti EdgeSwitch 5XP ES-5XP in Dubai, UAE
A five-port Gigabit switch for focused network deployments where compatible devices require individually controlled 24V passive PoE, straightforward browser-based management and a compact wall-mountable format.
Plan the correct configuration
Confirm endpoint voltage, power draw, port count, cabling and deployment conditions before ordering. Passive PoE compatibility is the most important check.
Direct answer for buyers
The Ubiquiti EdgeSwitch 5XP, model ES-5XP, is a compact managed switch with five 10/100/1000 Ethernet ports, a separate 10/100 management interface and configurable 24V passive PoE output. It is mainly used to connect and power compatible wireless radios, access points, cameras or other low-voltage network devices in small installations. It is worth considering when five data ports are sufficient and the connected equipment is explicitly designed for passive 24V input. Before proceeding, confirm each device’s voltage, polarity and maximum wattage, calculate the total PoE load, verify that standard 802.3af/at negotiation is not required, and review whether the available management functions match the intended network design.
What the ES-5XP does
The switch aggregates up to five Gigabit Ethernet connections and can deliver 22–24V DC passive power over the same cable to supported endpoints. Administrators can control PoE on a port-by-port basis, which makes it possible to mix compatible powered devices with ordinary non-PoE network equipment, provided each port is configured correctly.
A dedicated 10/100 management port gives installers an additional way to access the configuration interface without consuming one of the five main data ports. The product is intended for compact Layer 2 switching and power distribution rather than for replacing a router, enterprise core switch or standards-based PoE access switch.
Who should consider it
The ES-5XP may fit WISP cabinets, point-to-point radio sites, small surveillance nodes, workshop networks, temporary project offices and branch locations that already use compatible 24V passive PoE devices. It is particularly relevant when the installation needs only a few ports and values compact mounting more than expansion capacity.
It is not the right default for buyers who need IEEE 802.3af, 802.3at or 802.3bt negotiation, a large PoE budget, ten-gigabit uplinks, extensive redundancy or a cloud-managed UniFi switching experience. Those requirements should lead to a different model review.
Business challenges this compact switch can address
Limited equipment space
Small wall boxes and communications corners may not accommodate a rack switch. The ES-5XP provides five Gigabit ports in a compact enclosure that can be wall mounted where appropriate.
Separate power injectors
A group of compatible 24V devices can otherwise require several individual injectors. Centralising power at the switch can simplify the cabinet, but only after wattage and voltage are carefully checked.
Controlled remote endpoints
Per-port PoE control can support practical troubleshooting by allowing an administrator to disable and restore power to a compatible endpoint without physically unplugging its cable.
Small segmented networks
VLAN support and managed switching functions can help separate traffic in a modest deployment, subject to the wider router, addressing and security design.
Product-fit matrix
Use this matrix as an initial screening tool. Final suitability depends on the exact powered devices, cable runs, environmental conditions and management requirements.
| Requirement | Suitable when | Confirm before ordering |
|---|---|---|
| Port count | Five Gigabit device connections are enough | Uplink, spare-port and future growth needs |
| Power method | Endpoints explicitly support 24V passive PoE | Voltage, polarity, pin usage and device documentation |
| Power load | Each powered device stays within the port limit | Maximum device draw and total switch power budget |
| Management | Local EdgeSwitch XP management suits the team | Monitoring, backups, remote access and operational policy |
| Physical deployment | A compact wall-mountable switch is preferred | Ventilation, grounding, surge exposure and secure mounting |
Verified technical information
The values below correspond to Ubiquiti’s published ES-5XP specifications. Regional packaging and lifecycle availability should still be confirmed at quotation stage.
| Brand | Ubiquiti |
|---|---|
| Product name | EdgeSwitch 5XP |
| Model | ES-5XP |
| Product type | Managed Gigabit switch with configurable passive PoE |
| Networking interfaces | 5 × 10/100/1000 Ethernet ports |
| Management interface | 1 × 10/100 Ethernet port |
| Processor | MIPS 24K, 400 MHz |
| System memory | 64 MB |
| Code storage | 8 MB |
| PoE method | 24V passive PoE, configurable by port |
| PoE output voltage | 22–24V DC |
| Maximum PoE wattage per port | 11.5W |
| Power method | 24V DC, 2.5A adapter included according to manufacturer specification |
| Maximum power consumption | 60W |
| Dimensions | 197 × 87.5 × 27.3 mm |
| Weight | 250 g |
| ESD rating | Air/contact: ±24 kV |
| Mounting | Wall-mountable |
| Availability | Contact FourTeck for current UAE options and vendor lead time |
Critical compatibility notice: passive PoE is not standard PoE
The ES-5XP supplies passive voltage when PoE is enabled on a port. It does not rely on the powered-device negotiation used by IEEE 802.3af, 802.3at or 802.3bt equipment. Connecting an incompatible device to an energised passive PoE port can cause equipment damage. The endpoint documentation must clearly state support for the switch’s output voltage and wiring arrangement.
Do not assume that every Ubiquiti device, camera, telephone or access point accepts 24V passive PoE. Product families evolve, and later models may use standards-based PoE instead. Confirm the exact hardware revision and input specification of each endpoint rather than relying on brand name alone.
FourTeck can review a proposed device list and identify questions that should be resolved before supply. Final electrical compatibility remains dependent on the manufacturers’ specifications for the exact switch, powered device, cabling and installation environment.
A practical purchase and deployment journey
List all endpoints
Record the exact model, quantity, input voltage and maximum power draw of every connected radio, access point, camera or bridge.
Validate the design
Confirm port count, uplink topology, VLAN plan, total power demand, surge protection, grounding and physical mounting conditions.
Define supply scope
Specify switches, power accessories, patch leads, outdoor protection, installation materials and any configuration or documentation requirement.
Configure carefully
Connect and test non-powered links first, then enable passive PoE only on verified ports. Label powered ports and document the final settings.
Handover and maintain
Back up the configuration, record firmware details, monitor power load and keep the endpoint compatibility register current when devices are replaced.
Per-port power control for mixed small-site networks
One of the ES-5XP’s practical advantages is that passive PoE can be controlled on individual data ports. A site may therefore connect a compatible powered radio on one port, another passive-PoE endpoint on a second port and an ordinary unpowered Ethernet device on a third. The design remains safe only when the installer deliberately checks and configures each port.
This control can reduce the need for multiple injectors and may make troubleshooting easier. An administrator can power-cycle an eligible endpoint from the switch interface rather than visiting a difficult mounting location. That operational convenience is valuable for rooftop radios, pole-mounted links and compact surveillance nodes, but it should not replace disciplined fault analysis. Repeated power cycling can hide cabling, firmware or environmental problems that require permanent correction.
Port labels, configuration records and change control are strongly recommended. A future technician must be able to identify which ports carry passive voltage before moving patch leads or replacing equipment. The cost of a simple labelling process is small compared with the risk of energising an incompatible device.
Managed switching and VLAN planning
The EdgeSwitch XP interface provides management functions suited to a compact Layer 2 environment, including VLAN configuration. VLANs can help separate management, camera, wireless backhaul or user traffic, but the switch is only one part of that design. The router or firewall must provide the required inter-VLAN routing, addressing, access control and internet policy.
Before deployment, decide which ports operate as access ports, which links carry tagged traffic and how administrators will reach the management interface. An incorrect native VLAN or tagging choice can disconnect remote devices and make troubleshooting difficult.
For a small site, a simple documented VLAN plan is usually more valuable than excessive segmentation. FourTeck can help translate business groups and device types into a manageable network structure.
Compact form without ignoring site protection
The wall-mountable enclosure supports installations where rack space is unavailable, but compact size does not remove the need for professional power and cable planning. The switch should be mounted securely, kept within its supported environmental limits and installed where ventilation is not blocked.
Outdoor radios and long copper runs can expose network equipment to surges and electrical potential differences. Grounding, shielded cabling and appropriate surge-protection measures should be evaluated as part of the complete installation rather than treated as optional accessories after a fault occurs.
The published ESD rating is useful product information, but it should not be interpreted as a guarantee against lightning, poor grounding or severe power events. Site risk assessment remains necessary.
Ideal environments and realistic use cases
Wireless backhaul cabinet
Connect a small group of compatible point-to-point or point-to-multipoint radios while centralising passive power and management in a compact enclosure.
Small surveillance node
Support a limited camera or bridge arrangement only where every powered endpoint explicitly accepts the ES-5XP’s passive output and remains within the wattage limit.
Temporary project office
Provide managed switching for a modest site network where equipment is moved carefully and the compatibility register travels with the installation.
Workshop or warehouse zone
Create a small local distribution point for compatible industrial wireless links or monitoring devices, subject to temperature, dust, enclosure and cabling requirements.
Hospitality connectivity segment
Serve a focused building or outdoor connectivity area where five ports are sufficient and network support staff understand the passive-PoE design.
Replacement in an existing 24V design
Maintain a known compatible deployment after confirming the exact endpoint models, current firmware approach and regional product availability.
Integration and operational considerations
The switch should be evaluated as part of a complete network rather than as an isolated five-port component. The uplink must have enough capacity for the combined traffic of connected devices. Wireless backhaul radios, cameras and access points can generate very different traffic patterns, so port count alone is not a sufficient sizing method.
IP addressing, DHCP, DNS, routing and security policy are generally handled by upstream systems. Decide how the ES-5XP management address will be assigned, which administrators can reach it and how configuration backups will be stored. Where remote access is required, avoid exposing the management interface directly to the public internet. Use an appropriately secured management path determined by the wider network architecture.
Firmware should be reviewed before deployment and during maintenance cycles. Updates can correct defects or improve stability, but they should be tested against the site design and applied with a rollback plan. Record the installed version and retain a configuration backup before any change.
Cabling quality matters for both data and power. Long runs create voltage drop, and damaged connectors can cause unstable links or heat. Confirm cable category, conductor material, termination quality, shielding strategy and route conditions. For outdoor devices, coordinate surge protection and grounding with the building or site electrical design.
Questions to resolve before requesting a quotation
Which exact devices will receive power?
Provide model numbers and hardware revisions. Brand-level descriptions are not enough for passive-PoE approval.
How much power does each endpoint draw?
Use maximum input figures rather than normal operating estimates and keep reasonable design margin.
Will five ports remain sufficient?
Count uplinks, spare capacity, monitoring devices and likely expansion, not only the devices installed on day one.
What management workflow is expected?
Clarify local access, remote administration, configuration backups, monitoring and responsibility for firmware maintenance.
Where will the switch be mounted?
Review enclosure, ventilation, moisture, dust, temperature, grounding and physical access conditions.
Is installation support required?
Define whether the requirement covers supply only, pre-configuration, onsite mounting, testing, documentation or ongoing assistance.
Procurement checklist for the ES-5XP
✓ Confirm the exact model reference ES-5XP.
✓ State the required switch quantity and destination.
✓ List every powered endpoint by exact model.
✓ Verify 22–24V passive PoE compatibility.
✓ Check each device remains below 11.5W per port.
✓ Calculate the complete power budget with margin.
✓ Confirm whether five data ports allow future growth.
✓ Define VLAN, management and addressing requirements.
✓ Review cable length, conductor quality and termination.
✓ Include grounding and surge protection where relevant.
✓ Confirm mounting, ventilation and enclosure conditions.
✓ Request configuration, installation or handover scope when needed.
How FourTeck can assist with selection and deployment planning
FourTeck can help buyers turn a short product request into a clearer bill of materials. For the ES-5XP, that process should begin with endpoint compatibility rather than price alone. Share the exact radios, cameras, access points or bridge devices that will connect to the switch, together with quantity, cable distance, site type and expected traffic.
The team can assist with model confirmation, passive-PoE questions, alternative switch evaluation, quotation coordination and definition of optional configuration or installation work. Where the requirement forms part of a wider network, FourTeck can also discuss router, firewall, wireless, cabling and support considerations through its business technology services and network product portfolio.
The exact scope should be stated in the quotation. Supply, pre-configuration, onsite work, cable testing, documentation and ongoing support are separate activities unless expressly included. Use the FourTeck contact page to provide the requirement and request current guidance.
UAE availability and support guidance
Contact FourTeck to confirm current ES-5XP availability in the UAE. Supply can depend on quantity, regional channel availability, vendor lead time and the product’s current lifecycle position. A listing or published manufacturer page should not be interpreted as confirmation that a specific quantity is locally available.
For Dubai projects, provide the required quantity, intended endpoints, delivery location and preferred schedule. FourTeck can coordinate the quotation after reviewing the technical requirement. Installation and configuration should be requested as explicit line items when required, especially where passive-PoE validation, VLAN setup, mounting or onsite testing is expected.
Warranty terms, return conditions and regional support processes should be confirmed in the final commercial offer. Buyers planning a business-critical installation should also consider spare-unit strategy and replacement procedures because a compact switch can still represent a single point of failure.
Dubai, Abu Dhabi, Sharjah and Ajman project coverage
FourTeck can discuss product supply and project coordination for organisations operating across Dubai, Abu Dhabi, Sharjah and Ajman. The useful starting point is a consistent device schedule covering each site: switch quantity, powered endpoint models, cable lengths, management approach and installation expectations.
Multi-site buyers should avoid assuming that one configuration will suit every branch. A rooftop wireless node may need different surge protection and enclosure planning from an indoor office segment. Confirm each location’s power, grounding, access, environmental and support conditions before finalising the bill of materials. Delivery and service coordination can then be discussed according to the confirmed scope and regional scheduling.
GCC availability
Businesses planning ES-5XP deployments across GCC markets can contact FourTeck for requirement review, model confirmation and quotation coordination. Projects in the United Arab Emirates, Saudi Arabia, Kuwait, Qatar, Bahrain or Oman may have different commercial channels, delivery arrangements, electrical considerations and service possibilities. For this product, the most important technical step remains verification of each endpoint’s 24V passive-PoE input and power draw.
Share the destination country, quantity, site type, connected device schedule, preferred delivery window and any configuration or installation expectations. FourTeck can help define the requested scope and discuss suitable alternatives where the ES-5XP is unavailable or does not match the power standard. Product availability, delivery schedules, warranty handling, service visits and vendor lead times vary by country, quantity and project requirement. No local stock, customs outcome or fixed installation date should be assumed until the commercial and technical details are confirmed. Buyers with Kuwait requirements may also review FourTeck Kuwait information for relevant regional contact pathways.
Africa availability
Organisations planning compact wireless or surveillance networks in Africa can ask FourTeck to review the ES-5XP requirement together with compatible devices, accessories, cabling and support expectations. Conditions can vary significantly between indoor offices, remote wireless sites, hospitality properties and industrial locations, so the product should be assessed within the complete deployment rather than purchased only by port count.
Availability and fulfilment may depend on the destination, quantity, product lifecycle, shipping arrangements, vendor lead time, power requirements and local project conditions. Provide the destination country, exact endpoint models, required switch quantity, target schedule and any installation or remote-support scope. FourTeck can then discuss procurement planning and suitable alternatives without implying immediate shipment or country-wide onsite coverage. Businesses in East Africa can use the Kenya technology portal or Uganda technology portal, while wider enquiries can be directed through FourTeck Africa.
Related options and services to evaluate
Higher-port-count EdgeSwitch options
Consider a larger model when the design needs more endpoints, spare capacity, higher aggregate power or additional uplink choices. Specifications vary by model.
Standards-based PoE switches
Choose IEEE 802.3af/at-capable equipment when endpoints require PoE negotiation or when mixed-device safety and broader compatibility are priorities.
Surge protection and grounding
Outdoor links may require suitable Ethernet surge protection, shielded cable and coordinated grounding based on the site’s electrical design.
Network configuration support
Request assistance with management addressing, VLANs, port settings, documentation and handover where internal resources are limited.
Router and firewall integration
Confirm routing, DHCP, security policy and remote-management architecture for the wider network in which the switch will operate.
Installation and testing
Define mounting, cable testing, endpoint commissioning, labelling and configuration backup as part of the project scope when required.
Why businesses contact FourTeck
The main value is practical clarification before a purchase. A compact switch can appear simple, yet passive-PoE voltage, endpoint wattage, port planning and cabling conditions can determine whether it is appropriate. FourTeck can help organise those questions and identify missing information before the quotation is finalised.
Buyers also contact FourTeck for alternative-model guidance when their original selection lacks sufficient ports, uses the wrong PoE standard or does not align with their management platform. The objective is to match the bill of materials to the actual deployment rather than to force every requirement into one model.
Project assistance can include quotation coordination, configuration-scope definition, installation planning and support-pathway discussion. Learn more about the company through the FourTeck business profile.
Frequently asked questions
Is the Ubiquiti ES-5XP a five-port Gigabit switch?
Yes. It provides five 10/100/1000 Ethernet data ports. It also has a separate 10/100 Ethernet management interface.
Does it support standard 802.3af or 802.3at PoE?
No. The ES-5XP uses configurable 24V passive PoE. Buyers must verify that every powered endpoint supports the published 22–24V passive output and compatible wiring.
How much PoE power is available per port?
Ubiquiti publishes a maximum of 11.5W per PoE data port. The full design must also remain within the switch’s overall 60W maximum power specification.
Can PoE be enabled separately on each port?
Yes. Passive PoE is configurable by port, allowing powered and non-powered connections to coexist when each port is deliberately and correctly configured.
Is the ES-5XP suitable for cameras?
Only for camera models that explicitly accept the switch’s passive 24V output and stay within its wattage limits. Many cameras use standards-based PoE and should not be assumed compatible.
Can it be wall mounted?
Yes, the product is wall-mountable. The installer must still provide secure fixing, ventilation, suitable enclosure conditions and safe cable routing.
Does it replace a router or firewall?
No. It is primarily a managed Layer 2 switch. Routing, internet access, DHCP and security policy generally require upstream network equipment.
What information is needed for a UAE quotation?
Provide quantity, delivery location, connected-device model numbers, power requirements, cable lengths and any configuration or installation expectations.
Is the ES-5XP currently available in Dubai?
Availability should be confirmed at the time of enquiry because it can vary by quantity, regional supply and vendor lead time. FourTeck can coordinate a current check.
Can FourTeck assist with configuration and installation?
Configuration or installation assistance can be discussed and included in the quotation where required. The exact tasks, site access, cabling and handover requirements must be defined in advance.
Confirm the model, power compatibility and UAE supply scope
Send FourTeck the ES-5XP quantity, endpoint models, deployment location and required services. The team can review the key compatibility questions and prepare a quotation based on the confirmed requirement.
